Plumbing 101: What You Must Have for Installing a Bathtub

Click Here

This great article which follows pertaining to How to Install a Bathtub Yourself is absolutely informative. Check it out yourself and figure out what you think about it.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bathtub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably challenging task. If the old bathtub is easily available, the job can relocate quickly; if you need to open up a wall surface to eliminate the old bathtub and also place the new tub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will need a helper to leave the old bathtub and embeded in the new one. See to it you have qualified on your own for the job as well as are comfortable attempting it. Rather than hiring a service provider to take over a halfway-completed project, it is far better to consider employing one before you begin. Possibilities are you might need an expert plumber to make tube connections.
This post will certainly aid you set up a new tub in your bathroom if you have already bought a brand-new tub and also don't require to transform the setup of your previous supply of water pipelines.
Your devices as well as product list need to consist of the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the limited gain access to that is typically the instance.
    Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
    Before going on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
    If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next, position the tap in the mounting opening in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Protect the faucet in place with the supplier given backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type ought to be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Installing the Bath tub


    Making use of the two wooden boards under its feet, put the bath tub in the required position. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little points.
    The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the bath tub until the level reviews degree.
    To mount faucets, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
    Activate the water system and check all joints as well as new pipework for leakages and tighten them if necessary. Fill up the bath tub and also inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Ultimately, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bathtub should wait up until the bathtub has been used at least once as this will certainly settle it into its final placement.

    Planning for the Installment


    First of all, the supporting frame provided with the bath ought to be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to stop pressure on the tub.
    Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
    Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last position.

    Tiling Around the Bath tub


    In the location where the bathroom fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break an inflexible seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, bring about complications with dampness and also feasible leaks to the ceiling below.
    You can pick from a variety of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the tub is in use. The sealant can split relatively early if you do not consider this motion before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently readily available on the market. It is recommended to fit the tiles making use of waterproof or waterproof glue as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I came across that content on How to Install a Bathtub when doing a search on the internet. In case you enjoyed reading our page please remember to share it. Thank-you for taking the time to read it.


    For instant relief, call.

    Leave a Reply

    Your email address will not be published. Required fields are marked *